Skip to product information
Wall mount | Löwenstein prisma WM 090/100 TD + prismaAQUA
Wall mount | Löwenstein prisma WM 090/100 TD + prismaAQUA

Wall mount | Löwenstein prisma WM 090/100 TD + prismaAQUA

€44,99
SKU: CH-3040
plus €5.99 shipping
Colour
Version

Mount for secure, space-saving wall installation.

Compatibility
• Devices:
- WM 090 TD – prisma SMART/SOFT (including plus/max)
- WM 100 TD – 20A, 20C, CR, 25S, 25S-C, 25ST, 30ST, 30ST-C, 30ST-HFT, LAB, TIVAN
• Tubing: all compatible breathing tubes, including heated tubing
• Water tank: with prismaAQUA humidifier
• Modem module: side connection possible

Details
• Water tank easily removable from the side
• includes a hook-and-loop strap to secure the device
• optionally available with a cable box for storing the power supply

Package contents
• 1× wall mount with stops (pre-assembled)
• 1× Hook-and-loop strap
• 2× screws (4,5 × 50 mm)
• 2× Fischer DUOPOWER wall plugs (6 × 30 S LD)
• 2× washers
• for the “with cable box” version: 1× cable box including hook-and-loop strap and screws

Please also read the following notes and information about this product.

More mounts for prisma WM 090 TD →
More mounts for prisma WM 100 TD →

Questions or special requests?
Do you have questions about the product, is anything unclear, or would you like a custom adjustment? Feel free to contact us.
Stability & load capacity

The mount is made from high-quality PETG and is designed for continuous use.

• high impact resistance and dimensional stability
• UV- and water-resistant
• resistant to temperature fluctuations
• resistant to vibrations

• very sturdy construction thanks to well-designed geometry
• lasting secure support for your device

A short-term load test was carried out with a load of 12 kg without noticeable deformation.
Manufacturing process

This mount is manufactured using precision 3D printing. Each component then undergoes a careful visual inspection.

The manufacturing process may result in minor surface characteristics typical of printing.

  • without affecting stability, appearance or function.
  • not a quality defect
Assembly & installation

Tools required (tools are not included in the delivery.):

  • Drill bit (6 mm)
  • Torx T20
  • Allen key (2,5 mm, only for the version with cable box)

Note: Please refer to the video.

  1. Hold the mount in the desired position and mark the drill holes.
  2. Drill at least 50 mm into the wall using a 6-mm drill bit.
  3. Insert the wall plugs fully and flush with the surface.
  4. Secure the mount using the supplied Torx screws and washers.
  5. Only for the version with cable box:
    5.1. Attach the cable box to the mount using the supplied countersunk screws and nuts.
    5.2. Store the power supply and cables in the cable box.
    5.3. Place the additional hook-and-loop strap around the cable box.
    5.4. Fit the lid and secure it with the hook-and-loop strap.
  6. Insert the device as shown in the video and gently tighten the hook-and-loop strap.

For installation on other surfaces, you must select suitable fixings yourself. Use of the washer is recommended to provide a larger bearing surface.
Shipping & delivery time

• shipped from Germany
• usually processed within 1–3 working days
• delivery then takes a few working days, depending on the delivery area
• tracking available after dispatch

Note on shipping to Switzerland:
Additional customs clearance fees may apply.
Based on experience: approx. 7.7 % import tax + approximately 11–18 CHF (CH-Post/DHL).
The recipient bears these fees. Information provided without guarantee.
Safety & liability

Please observe the following instructions for safe use:

• installation is carried out at your own responsibility
• check the mounting surface and wall condition before installation
• use suitable fixings for the mounting surface
• regularly check that the mount and fixings are secure

Liability for damage resulting from improper installation, an unsuitable mounting surface, overloading or external forces is excluded.

No liability is accepted for indirect or consequential damage, in particular to the mounted device.
Product & material information

• not suitable for children – choking hazard from small parts
• use only for the intended purpose
• PETG can soften at temperatures from approx. 70 °C

Disposal:
• dispose of PETG components and the hook-and-loop strap with plastic waste
• dispose of screws and washers with metal waste

Manufacturer details

Marc Fenzl
cpap-halterungen.de
Peter-Michels-Str. 49
50827 Köln
Germany
Email: info@cpap-halterungen.de