Skip to product information
Wall Mount Basic | ResMed AirSense 11
Wall Mount Basic | ResMed AirSense 11

Wall Mount Basic | ResMed AirSense 11

€27,99

plus shipping costs
Color

Wall mount for ResMed AirSense 11 for secure and space-saving wall installation.

• Suitable with and without water tank  
• Simple screw installation  
• Hook-and-loop strap for positioning and securing the device  
• Available in various colors: white, black, gray (see example image)

Please note the mounting orientation: The hose connection points away from the wall, allowing particularly close-to-wall positioning of the device.

Scope of delivery
• 1× Mount (consisting of 3 individual parts)  
• 8× Countersunk screws (M4 × 12)  
• 8× Safety nuts (M4)  
• 1× Hook-and-loop strap  
• 2× Screws (4.5 × 50 mm)  
• 2× Fischer DUOPOWER wall plugs (6 × 30 S LD)  
• 2× Washers
Stability & Load Capacity

The mount is manufactured from high-quality PETG and is designed for long-term use.

• High impact resistance and dimensional stability
• UV and water resistant
• Resistant to temperature fluctuations
• Resistant to vibrations

• Very stable construction due to a well-engineered geometry
• Provides a secure hold for your device over the long term

As part of a short-term load test, a load of 14 kg was tested without any visible deformation.
Manufacturing Process

This mount is manufactured using a precise 3D printing process. Each component undergoes a careful visual inspection.

Due to the manufacturing process, minimal print-typical surface characteristics may occur.

• Without any impact on stability, appearance, or function
• Not a quality defect

Installation & Setup

1. Assemble the mount

Required tools (tools are not included):
• Allen key (2.5 mm)

1. Place the individual parts into the assembly position as shown in the illustration.
2. Insert the safety nuts into the designated hexagonal recesses (the retaining ring must face outward).
3. Insert the screws.
4. Lightly tighten the screws. A slight resistance is sufficient.

2. Mount the holder on the wall

Required tools (tools are not included):
• Drill bit (6 mm)
• Torx T20

1. Hold the holder at the desired position and mark the drill holes.
2. Drill at least 50 mm deep into the wall using a 6 mm drill bit.
3. Insert the wall plugs fully and flush with the surface.
4. Fasten the holder using the supplied Torx screws and washers.
5. Insert the device as shown in the illustration and lightly tighten the hook-and-loop strap.

For installation on other surfaces, suitable fastening material must be selected by the user.
The use of washers is recommended to achieve a larger contact surface.
Shipping & Delivery

• Shipping from Germany
• Processing typically within 1–3 business days
• Delivery is carried out afterwards, depending on the delivery region, within a few business days
• Shipment tracking available after dispatch

Note on shipping to Switzerland:
Additional customs clearance fees may apply.
Estimated values: approximately 7.7% import VAT plus around 11–18 CHF (Swiss Post / DHL).
All fees are to be borne by the recipient. Information provided without guarantee.
Safety & Liability

Please observe the following safety instructions for proper use:

• Installation is carried out at your own responsibility
• Check the surface and wall condition before installation
• Use suitable mounting hardware appropriate for the surface
• Regularly check the mount and fasteners for a secure fit

Liability for damage resulting from improper installation, unsuitable surfaces, overloading, or external forces is excluded.

No liability is assumed for indirect damage or consequential damage, particularly to the mounted device.
Product & Material Information

• Not suitable for children – choking hazard due to small parts
• Use only for the intended purpose
• PETG may soften at temperatures above approximately 70 °C

Disposal:
• Dispose of PETG components with plastic waste
• Dispose of screws and washers with metal waste